R1a = 2,2 K
R1b =470 Ohm
R2 = 10 K
R3, R7 = 3.3 k
R4 = 390 Ohm
R5 = 47 K
R6 = 3.3 K 1Watt
R8 = 180 Ohm
R9, R10 = 0.47 Ohm 3Watt
R11 = 0.075 Ohm 2Watt
R12 = 470 Ohm
P1 = 500K liner potentiometer
P2 = 4.7 K potentiometer
P3 = 10 K potentiometer
C1 = 1nF
C2 = 10nF
C3 = [...]
This circuit is very basic to build. To open a lock which is connected to the K1 Load, you must press each momentary switch in the correct sequence. The sequence used in this circuit is S1, S2, S3 and finally S4. If any of the other switches are pressed the circuit will be reset and [...]
The circuit presented here is a simple audio/video transmitter with a range of 3 to 5 metres. The A/V signal source for the circuit may be a VCR, a satellite receiver or a video game etc. A mixer which also operates as an oscillator at VHF (H) channel 5 TV frequency is amplitude modulated by [...]
C1, C2, C3, C4 = 10 – 80pF
C 5 = 10nF
C6 = 1000pF
C7 = 100nF
C8 = 2200mF/35V
L1 = 1 coil with diameter of 10 mms, 1 mm
L2 = 7 coils with diameter of 10 mms, 0,8 mm
L3 = 3 coils with diameter of 10 mms, 1 mm
TR1 = BLY89
RFC [...]
This digital thermometer use DS1820 measurement temperature from 0-99 ‘C then
the temperature will display on LCD 1X16 .The CPU used in this project is PIC16F84A.
Software programming with CCS C Compiler.
Download CCS Source code
This circuit uses an MC2830 to form a voice activated switch ( VOX ). A traditional VOX circuit is unable to distinguish between voice and noise in the incoming signal. In a noisy environment, the switch is often triggered by noise, or the activation sensitivity must be turned down. This circuit overcomes this weakness. The [...]
From http://www.elecfree.com/circuit/electronic-control/sound-scr-swith-by-ic-1458-scr-c106d/
We have all seen the commercial on TV ………. CLAP – ON – CLAP – OFF – THE – CLAPPER ………… well here is a circuit that will perform that same function.
Circuit operation is as follows. A single hand clap will be picked up by the electric mic which is coupled through C1 into the [...]
This project allows instant start sequentially but a dozen low-voltage lamps 12 V / 60 W, and makes them fade and always sequentially (but slower). This system has been designed to meet the demand of a visitor who wanted ten recessed low voltage spot in a driveway to his house, with the following function: – [...]
This circuit allows switching on a LED when the battery voltage (12V) drops below a certain threshold. The operating system is based on a comparison of tension, which comes in a zener diode. If the supply voltage is 12V and the zener diode is a 10V model (this is the case in the diagram), we [...]
This is a good looking and practical device that can be useful in many areas where countdown timer is needed. This project is based on the PIC16F84A microcontroller. The time range can be adjusted between 1 and 999 seconds. This project has 3 buttons and one of them is named Set Button. In order to [...]
A VU meter is often included in audio equipment to display a signal level in Volume Units; the device is sometimes also called volume indicator (VI). In this project we are building a basic and low cost LED VU Metre circuit . The extent (range) display is -18 dBu to +3 dBu, spread over [...]
Today we have a new category “Projects” and a new electronic project 12 Channel LED Chaser with PIC16F84A.
This project is based on the popular PIC16f84A micro-controller.The heart of this project LED chaser is the PIC16F84A PIC microcontroller.A 4MHz crystal and capacitors C1 and C2 22pf is used for providing clock pulses to the micro-controller. The [...]
